top of page
Frequently Asked Questions
Top 15 Water Treatment Questions
There are salt-free water treatment systems, but they are not technically water softeners.
A true water softener uses an ion-exchange process to remove calcium and magnesium—the minerals responsible for hard water—and requires salt or potassium chloride for regeneration.
Salt-free systems generally condition the water rather than actually removing the hardness.
No. A properly operating water softener does not add salt directly to your drinking water.
The salt is used during the regeneration process to recharge the softener resin. The amount of sodium added to the water depends on factors such as the hardness of your water and how the softener is programmed.
If you're concerned about sodium in your drinking water, there are options we can discuss, including reverse osmosis drinking-water systems.
Yes, in most residential applications, you can.
Modern water softeners are much more efficient than older systems and use significantly less water and salt during regeneration.
A properly sized softener may use approximately 75 gallons of water during a regeneration cycle and typically regenerates only 2–4 times per month, depending on household water usage, water hardness, and system settings.
For comparison, the average person uses approximately 60 gallons of water per day for normal household activities.
The biggest consideration with a septic system is hydraulic load—the total amount of water entering the system. With a properly sized and programmed softener, the additional water from regeneration is relatively small compared with the overall household water usage.
As always, if you have specific concerns about your septic system, we recommend discussing them with your septic professional.
Maybe—but water treatment isn't one-size-fits-all.
Two homes next door to each other can have very different water chemistry, well conditions, flow rates, and water usage.
Your neighbour's system can certainly give us a starting point, but we recommend testing your water and selecting equipment based on your specific water quality and household needs.
It depends on the equipment, water quality, and maintenance.
Many quality treatment components can provide 10–15+ years of service, while some filters and treatment media will need to be replaced much sooner.
Proper sizing, regular maintenance, and monitoring your water quality can significantly extend the life of your system.
For most homes, we recommend changing your filters once a year as part of regular maintenance.
If you have troublesome water—such as high sediment, iron, manganese, sulphur, or other water-quality issues—you may need to change your filters more frequently.
Regular filter changes help maintain good flow, protect your treatment equipment, and ensure your system continues to perform properly.
There isn't a set replacement schedule for treatment media.
How long a media bed lasts depends on the type of media, your incoming water quality, water usage, and how well the system is maintained.
Some media can last many years, while other applications may require more frequent replacement.
Rather than replacing media simply because it has reached a certain age, we recommend testing the water and checking the performance of the system to determine when a re-bed is actually required.
Our free onsite water test is a basic screening of your home's water.
We test for:
• pH
• Hardness
• Iron
• Manganese
• TDS (Total Dissolved Solids)
• Colour
• Odour
This gives us a good starting point for understanding your water and identifying potential treatment needs.
Our onsite testing is a screening test and is not a certified laboratory analysis. If more detailed or certified testing is required, we can recommend appropriate laboratory testing.
For general water quality, we recommend testing your water at least every two years.
Health Canada recommends private well owners test their general water quality every two years. It's also important to remember that bacterial testing is different. Health Canada recommends testing private well water for E. coli and total coliforms at least every six months.
If you have a water treatment system, we recommend testing both before and after treatment to make sure the system is doing what it's designed to do.
If your system is specifically treating a contaminant such as arsenic, lead, uranium, or another heavy metal, regular testing becomes even more important. Periodic testing helps confirm that the treatment system is continuing to effectively remove contaminants and that the equipment or filtration media is performing as intended.
You should also test sooner if you notice a change in the colour, taste or smell of your water, or after well repairs, flooding, heavy rainfall, or any other event that could affect your water supply.
When it comes to water treatment, testing is the only way to know for sure that your system is still doing its job.
We recommend using a good-quality water softener salt specifically intended for water softeners. High-quality pellets generally contain fewer impurities and can help keep your brine tank and softener operating properly.
If you're unsure what salt to use, ask us. We're happy to recommend the right product for your system.
We recommend keeping your brine tank between 1/3 and 2/3 full of salt.
There is no need to keep the tank completely full. In fact, allowing the salt level to drop helps you see that the system is actually using salt and can help prevent salt bridging.
A salt bridge occurs when the salt forms a hard crust or bridge in the tank, preventing the water from properly dissolving the salt underneath. Keeping the tank excessively full can increase the chance of this happening.
The exact amount of salt your system uses depends on the size of the softener, water hardness, household water usage, and how the system is programmed.
Our recommendation: Keep it between 1/3 and 2/3 full, and don't let it run completely empty.
It's completely normal for the water level in your brine tank to change throughout the regeneration process.
The brine tank contains both salt and water. During regeneration, the softener draws brine from the tank, which lowers the water level. The system then adds water back to the tank to prepare the brine for the next regeneration.
Depending on how much salt is in the tank, you may see water at the bottom, or you may not see it at all. Not seeing water does not necessarily mean there is a problem.
What matters is that the system is properly drawing and refilling the brine tank during regeneration.
Most water treatment systems are programmed to regenerate or backwash at a specific time, usually during the night when water usage is low.
If your system is backwashing during the day, the regeneration time may have been changed, the clock may be incorrect, or the system may have been programmed to regenerate at a different time.
The exact procedure for changing the time depends on the control valve on your system. If you're unsure how to change it, give us a call and we can walk you through it or show you how to set it properly.
If you're leaving your home for an extended period, the best approach depends on how long you'll be away and what type of treatment system you have.
Simply unplugging the system isn't always the best option, because the system may lose its programmed settings or the clock may stop keeping time.
For many systems, putting the equipment into bypass and shutting off the water supply is a better option for an extended absence. However, some situations may call for the system to be drained or handled differently.
If you're going to be away for an extended period, contact us before you leave. We can recommend the appropriate procedure for your specific system.
Our onsite water testing is an excellent screening tool, but it isn't a substitute for certified laboratory analysis.
If you're relying on a private well for your drinking water, laboratory testing gives you a much more complete picture of what's actually in your water. A lab can test for contaminants that cannot be identified through basic onsite testing, including bacteria, nitrates, arsenic, lead, uranium and other substances.
This is especially important when installing or maintaining a treatment system designed to remove a specific contaminant. Testing the water before and after treatment can confirm that the treatment system is actually doing what it's designed to do.
If you're drinking the water, you should know what's in it—not just what it looks or tastes like.
bottom of page
